Differences

This shows you the differences between two versions of the page.

--- announce [2010/02/04 09:31]
twdorris
+++ announce [2014/12/08 21:43]
twdorris removed
@@ Line 1: / Line 1: @@
-====== Product Announcements  - February 4, 2010 ======
+====== Product Announcements  - October 19, 2010 ======
 We're constantly working to improve our products and roll in various requests from our users.  This page will contain some updates on what we're spending our time on.
 ===== Release date =====
 I know the first question coming is "when".  As soon as we know, we'll post it.  I promise.  I'd rather wait until we are sure about a release date than to keep posting made-up dates and missing them.  The very minute we feel comfortable enough with a release candidate to schedule a date, we'll post it up.
-===== V3Lite =====
-As promised, we have released [[http://www.ecmtuning.com/product/v3lite|V3Lite]] for the 1G and 2G DSMs.  We have posted a [[prodcompare|product comparison table]] for review.
-We do already have a few changes in mind for this product.  In particular, we expect to move the injector compensation from direct access into the ECU Config area because unlike most other direct access tables, changes to the deadtime table and even to the global fuel scale are just more convenient in the ECU Config area where they can be made as the engine is running.
-===== Individual deadtime control =====
-We've tested the idea of doing individual deadtime control and we really liked [[http://www.youtube.com/user/ecmtuning#p/a/u/1/cO7fPmAxG50|the results]].  Basically, you can dial in different deadtime values for each injector.  This lets you fine tune the behavior of injector sets that aren't match perfectly at idle pulsewidths.  Most places are not able to properly test injectors with our ECU drivers and at our typical idle pulsewidths.  So while the injectors they ship may be well matched at 100%, 80% or even 20% duty cycle, they can still be VERY different at idle due to variations in deadtime from one to the next.
-In addition to controlling individual deadtime, we will be increasing deadtime resolution as well.  The factory 1G ECU runs with a resolution of 24usecs and the 2G runs with 15usecs.  ECMLink normalizes these so that both are 15usecs, but even this can be too coarse for large injectors.  Running 1750s with 15usecs "jumps" in injector pulsewidth at idle is just too much.
-We will increase this resolution to 4usecs to match the hardware limitations inside the ECU.  Doing so makes for much nicer idle quality with large injectors.
 ===== 2G DSM non-EPROM conversion =====
-{{http://www.ecmtuning.com/images/photos/noneprom2g.jpg?95x100  }}Yes, we're finally nearing completion of this project.  We've had the 1G DSM non-EPROM conversion out for a while, but the 2G version was really MUCH more difficult in terms of both design and fabrication.  Unfortunately, I don't expect we'll be able to offer this conversion at the same price as the 1G.  The component costs are just astronomical.  But, we're at a point where it doesn't make sense to halt the project, so we'll push it through and when someone really needs it, we'll be able to help them out.
+{{http://www.ecmtuning.com/images/photos/noneprom2g.jpg?95x100  }}  We can FINALLY say we're able to convert non-EPROM 95, 96 and 97 2G DSM ECUs!  This has taken a LOOONG time to complete, but we're finally there!  The result is a work of art and we hope will provide some much needed help to those looking for 2G ECUs to use with ECMLink.
-Click image to enlarge.
-===== Native 2G MAF connector =====
-{{http://www.ecmtuning.com/images/photos/2gmafconnectors.jpg?200x130  }}IMO, this is one of the coolest things we've done in a long time.  It seems so simple at first, but nobody else in the world has this connector.  We had to custom design, prototype and mold this piece ourselves.  It's basically the mating piece to the 2G MAF connector on the car's wiring harness.  It's a properly sealed solution that doesn't exist anywhere else.
-We will be using this connector on our GM MAF adapters to finally provide a true plug-n-play solution for 2G DSMs.  The 1G guys already have this because their mating connector already exists.  We're finally catching the 2G guys up.  :-P  Prior to this connector we (and everyone else) had been using a Delphi equivalent that just happened to sorta shove into place but was seriously lacking in a number of ways including the lack of a locking tab, improper fit and no sealing mechanism at all.
 Click image to enlarge.
@@ Line 56: / Line 15: @@
 One of the next items on our to-do list is a quick-connect feature to provide for near instant connect speeds with the ECU by caching configuration data on the laptop.  The application will always know whether its cache of data matches the ECUs by a complex checksum algorithm.  But details aside, the idea is to reduce that lengthy configuration read step to near zero.
 ===== Live edit =====

ECMTuning - wiki

User Tools

Site Tools

Differences

Page Tools