ECMTuning - wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

<h1>ECU Input Impedance Mismatch</h1> <div class="level1"> <p> There are a number of analog inputs available on the 1G and 2G ECU. Many are used for critical engine operation, but some are available for datalogging <a href="/wiki/doku.php?id=externalsensorlist" class="wikilink1" title="externalsensorlist">aftermarket sensors</a>. The problem is that some of these inputs are incompatible with some aftermarket sensors. In particular, the 1G EGR temperature input and the 2G baro input have pull up/pull down resistor configurations that some sensors are not capable of driving properly. The solution to this is to "buffer" the input so that the sensor is not directly driving the ECU's input. The circuit and buffer board described below can be used for this purpose. The picture below illustrates the buffer board available for purchase from ECMTuning. </p> <p> <a href="/wiki/lib/exe/fetch.php?tok=7eb3d4&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2Ftypicalinstall.gif" class="media" title="http://www.ecmtuning.com/images/forums/typicalinstall.gif"><img src="/wiki/lib/exe/fetch.php?tok=7eb3d4&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2Ftypicalinstall.gif" class="media" alt="" /></a> </p> <p> <b>12/19/2007:</b> We are now accepting orders for these completed units. We have several in stock, ready to ship. </p> <p> <a href="http://www.ecmtuning.com/ordering-buffer.html" class="urlextern" title="http://www.ecmtuning.com/ordering-buffer.html" rel="nofollow">http://www.ecmtuning.com/ordering-buffer.html</a> </p> </div> <h1>Details</h1> <div class="level1"> <p> The following table lists a set of ECU inputs and their internal pull up/pull down resistor configuration. </p> <span class='np_break'> </span> <div class="table"><table class="inline"> <thead> <tr class="row0"> <th class="col0"> Input </th><th class="col1"> 1G </th><th class="col2"> 2G </th> </tr> </thead> <tr class="row1"> <td class="col0"> EGRTemp </td><td class="col1"> 10k up </td><td class="col2"> - </td> </tr> <tr class="row2"> <td class="col0"> Baro </td><td class="col1"> float/100k down? </td><td class="col2"> 3.3k down </td> </tr> <tr class="row3"> <td class="col0"> IAT </td><td class="col1"> 2.2k up / 39k down? </td><td class="col2"> 2.2k up / 39k down? </td> </tr> <tr class="row4"> <td class="col0"> Coolant </td><td class="col1"> 2.2k up / 39k down? </td><td class="col2"> 2.2k up / 39k down? </td> </tr> <tr class="row5"> <td class="col0"> MDP </td><td class="col1"> - </td><td class="col2"> 100k down </td> </tr> </table> <span class='np_break'> </span> </div> <p> Again, the EGRTemp on a 1G and the Baro input on a 2G are problematic for some aftermarket sensors. When feeding certain wideband kits into the EGRTemp input on a 1G, for example, you may see normal A/F ratio readings above 11.5:1 but then the readings flatline there and won't show any value below that. </p> <p> For 2Gs, feeding an aftermarket pressure sensor into the Baro input can produce a cap on the upper value read by the sensor. A 3.3-bar sensor, for example, might flatline at 2.5-bar. For the 2G Baro issue, there's a fairly simple solution if you're handy with a soldering iron (or two). The <a href="/wiki/doku.php?id=2gbaroinputworkaround" class="wikilink1" title="2gbaroinputworkaround">2G baro input workaround</a> page describes this solution. </p> <p> In either case (1G or 2G) and for just about any input, you can also consider using a unity buffer to drive the ECU. Such a device presents a low-load input for connecting the external sensor and then produces a higher drive output for connecting to the ECU's input. The following schematic can be used to build this device. </p> <p> <a href="/wiki/lib/exe/fetch.php?tok=ca8b90&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2FBuffer.JPG" class="media" title="http://www.ecmtuning.com/images/forums/Buffer.JPG"><img src="/wiki/lib/exe/fetch.php?tok=ca8b90&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2FBuffer.JPG" class="media" title="Diagram" alt="Diagram" /></a> </p> <p> Note that this is not necessarily an easy thing to do. The op-amp part referenced in that diagram is extremely small and difficult to work with if you're not familiar with SMT techniques or have access to appropriate equipment. </p> <p> If you can't wait and working with a SOT23-5 package is just too small for you, then consider this circuit/chip instead. It's a bit easier to work with. </p> <p> <a href="/wiki/lib/exe/fetch.php?tok=8ee717&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2FBufferDIP.JPG" class="media" title="http://www.ecmtuning.com/images/forums/BufferDIP.JPG"><img src="/wiki/lib/exe/fetch.php?tok=8ee717&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2FBufferDIP.JPG" class="media" title="Diagram" alt="Diagram" /></a> </p> </div>