externalsensorinput
Differences
This shows you the differences between two versions of the page.
|
externalsensorinput [2009/09/22 14:57] twdorris |
externalsensorinput [2024/03/15 11:16] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Available ECU inputs ====== | ||
| - | |||
| - | Note that the following lists out all the available inputs on the 1G and 2G DSM ECUs. Most of these have special cases associated with them to be useful as a general purpose analog input. The most freely available inputs are the EGRTemp input on a 1G ECU and the RearO2 and MDP inputs on the 2G ECU. The rest have special cases to consider with them. Some may even require a [[ECUInputData|buffer circuit]] to be driven properly, depending on which sensors is connected to which input. | ||
| - | |||
| - | Reference: [[ecuwiringinformation|ECU Wiring Docs]] | ||
| - | |||
| - | ===== 1G ECU ===== | ||
| - | |||
| - | * EGR Temp Input (ECU Pin 15) | ||
| - | * IAT Input (ECU Pin 8) - **see IAT/Baro Notes below** | ||
| - | * Baro Input (ECU Pin 16) - **see IAT/Baro Notes below** | ||
| - | * Front O2 (ECU Pin 4) - **Only usable when "Open Loop" option is selected (V2 or V3), or narrowband O2 simulation is enabled (V3 only).** | ||
| - | * Coolant Temp Input (ECU Pin 20) - **(V3 only) - This will leave the car in "Open Loop".** "Lock Coolant Temp" must be selected, to work properly. | ||
| - | |||
| - | |||
| - | ===== 2G ECU ===== | ||
| - | |||
| - | * Rear O2 (ECU Pin 75) | ||
| - | * MDP (ECU Pin 73) | ||
| - | * Baro (ECU Pin 85) - **see IAT/Baro Notes below - Has internal pull down resistor making it unsuitable for certain sensors (see [[2gBaroInputWorkaround|work around]]).** | ||
| - | * IAT (ECU Pin 72) - **see IAT/Baro Notes below** | ||
| - | * Coolant Temp Input (ECU Pin 83) - **(V3 only) - This will leave the car in "Open Loop".** "Lock Coolant Temp" must be selected, to work properly. | ||
| - | |||
| - | ===== EVO1-3 ECU ===== | ||
| - | |||
| - | * Front O2 (ECU Pin 56) | ||
| - | * Baro (ECU Pin 65) - **see IAT/Baro Notes below - Has internal pull down resistor making it unsuitable for certain sensors (see [[e3baroinputworkaround|work around]]).** | ||
| - | * IAT (ECU Pin 52) - **see IAT/Baro Notes below** | ||
| - | * Coolant Temp Input (ECU Pin 63) - **This will leave the car in "Open Loop".** "Lock Coolant Temp" must be selected, to work properly. | ||
| - | |||
| - | |||
| - | ====== IAT/Baro Notes ====== | ||
| - | In order to free up the IAT and Baro inputs to the ECU, you must be running a non-Mitsubishi style mass airflow sensor. That can either be a GM MAF connected to the ECU with our GM MAF cable or it can be a GM MAF connected to the ECU through a MAF translator. Or it can even be while running speed density mode in ECMLink. | ||
| - | |||
| - | The point being that you can NOT log an aftermarket sensor on these inputs if you are running a Mitsubishi style mass airflow sensor (1G DSM, 2G DSM, EVO8). | ||
| - | |||
| - | In addition, if you are running a GM MAF with a MAF translator, then you must also make sure you have selected to [[ignoreiatbaro|Ignore IAT/Baro]]. | ||
externalsensorinput.txt ยท Last modified: 2024/03/15 11:16 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
