ECMTuning - wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

<h1>How-To's</h1> <div class="level1"> <p> This page is a collection of how-to's from those that have-done. </p> </div> <h2>Hardware</h2> <div class="level2"> <ul> <li class="level1"> <a href="/wiki/doku.php?id=swapplugwires" class="wikilink1" title="swapplugwires">2G plug wire swap</a> - Installing DSMLink in a car without a '95/'96 style cam angle sensor</li> <li class="level1"> <a href="/wiki/doku.php?id=90clutchcut" class="wikilink1" title="90clutchcut">Clutch cut wire on a '90 DSM</a> - Installing a clutch cut (NLTS) wire in a 1990 DSM</li> <li class="level1"> <a href="/wiki/doku.php?id=nitrouscontrolwiring" class="wikilink1" title="nitrouscontrolwiring">Basic "nitrous" controls</a> - The basics of wiring up a solenoid to be control by DSMLink's "nitrous" controls</li> <li class="level1"> <a href="/wiki/doku.php?id=nitrouscontroldetails" class="wikilink1" title="nitrouscontroldetails">"Nitrous" control specifics</a> - More specific information about DSMLink's control of the FPR solenoid output</li> <li class="level1"> <a href="/wiki/doku.php?id=usenitrouscontrolsfordejontoolbovmod" class="wikilink1" title="usenitrouscontrolsfordejontoolbovmod">"Nitrous" control used for BOV bypass mod</a> - Describes one alternative use of DSMLink's "nitrous" controls</li> <li class="level1"> <a href="/wiki/doku.php?id=installnewsensor" class="wikilink1" title="installnewsensor">Install a sensor for datalogging</a> - Describes how to use a non-factory sensor for datalogging (e.g., a boost sensor, a wideband kit, etc.)</li> </ul> </div> <h2>Tuning/dial-in</h2> <div class="level2"> <ul> <li class="level1"> <a href="/wiki/doku.php?id=basicfueladj" class="wikilink1" title="basicfueladj">Changing injectors</a> - Describes how to adjust DSMLink for different injectors</li> <li class="level1"> <a href="/wiki/doku.php?id=v3mafadjcombft" class="wikilink1" title="v3mafadjcombft">General MAF calibration</a> - How-to on general MAF calibration with the V3 application</li> <li class="level1"> <a href="/wiki/doku.php?id=maftcalibrationbywbo2" class="wikilink1" title="maftcalibrationbywbo2">MAFT Calibration using a WBO2</a> - Describes how to calibrate a MAFT output using a WBO2</li> <li class="level1"> <a href="/wiki/doku.php?id=maftcalibrationbyloggedboost" class="wikilink1" title="maftcalibrationbyloggedboost">MAFT Calibration using a boost sensor</a> - Describes how to calibrate a MAFT output using a boost sensor</li> <li class="level1"> <a href="/wiki/doku.php?id=createvolumetricefficiencymap" class="wikilink1" title="createvolumetricefficiencymap">Customize the VE table for your setup</a> - Create a VE table more suited to your specific setup</li> <li class="level1"> <a href="/wiki/doku.php?id=v3tpsadj" class="wikilink1" title="v3tpsadj">How to dial in TPS/idle switch</a></li> </ul> </div> <h2>Direct Access</h2> <div class="level2"> <ul> <li class="level1"> <a href="/wiki/doku.php?id=direct_access_changes" class="wikilink1" title="direct_access_changes">Direct Access changes</a> - Describes how to add custom changes to Direct Access</li> </ul> </div>