User Tools

Site Tools


installnewsensor

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
installnewsensor [2008/01/23 07:50]
76.100.119.159
installnewsensor [2024/03/15 11:16] (current)
Line 1: Line 1:
-====== ​External sensor installation ​====== +====== ​Aftermarket Sensor Installation ​====== 
-You can datalog a number of aftermarket sensors with DSMLink.  These primarily include pressure sensors, temperature sensors, and wideband kits.  For a complete list of supported sensors, visit the [[ExternalSensorList|supported sensors]] page.  Regardless of which sensor is being used, the process for installation is almost always the same.  You start by installing the sensor according to the manufacturer'​s installation instructions. ​ This will include running power and ground and whatever else the sensor needs to get.  Once that's done and the sensor appears to be installed and working properly, you select an [[ExternalSensorInput|available input]] on the ECU to which you will connect the sensor'​s output. ​ You disconnect the factory sensor that was providing signal data to the ECU on the selected line and then connect your new sensor'​s output instead.+You can datalog a number of aftermarket sensors with ECMLink.  These primarily include pressure sensors, temperature sensors, and wideband kits.  For a complete list of supported sensors, visit the [[ExternalSensorList|supported sensors]] page
 + 
 +The following is a high-level overview of the process of connecting an aftermarket sensor to the ECU for logging.  Regardless of which sensor is being used, the basic process for installation is almost always the same.  ​ 
 + 
 +  - You start by installing the sensor according to the manufacturer'​s installation instructions. ​ This will include running power and ground and whatever else the sensor needs to get. 
 +  Once that's done and the sensor appears to be installed and working properly, you select an [[ExternalSensorInput|available input]] on the ECU to which you will connect the sensor'​s output. 
 +  You disconnect the factory sensor that was providing signal data to the ECU on the selected line and then connect your new sensor'​s output instead.  Locate the sensor'​s output from the manufacturer'​s installation instructions. ​ You will be looking for a 0-5v analog output of some sort. 
 +  - Once that's done, go into the **ECU Inputs** tab and assign the sensor to an input pin for logging (be __sure__ to hit "Save Pin Assignments"​ after making a change to the pin assignments). ​ Once you've done that, you can add the sensor to the ECU's list of things to log by pulling up the Captured Values dialog (F10).
  
-Once that's done, you go into DSMLink'​s ''​ECU->​Captured values''​ dialog and datalog the new sensor. ​ That's about it.  Some sensor'​s will have some special cases to consider, though, as do certain ECU inputs you want to use.  So carefully read through the pages below to familiarize yourself with all this information before you proceed. 
  
 ===== Basics ===== ===== Basics =====
  
 +  * [[WidebandBasics|Wideband basics]] - The basics behind wiring up an aftermarket wideband kit
   * [[ExternalSensorInstall|Basic installation example]] - Describes the basic process using a Zeitronix WBO2 installed on a 1G as an example   * [[ExternalSensorInstall|Basic installation example]] - Describes the basic process using a Zeitronix WBO2 installed on a 1G as an example
   * [[ExternalSensorInput|Available ECU inputs]] - A list of available ECU inputs to which you can consider connecting an external sensor   * [[ExternalSensorInput|Available ECU inputs]] - A list of available ECU inputs to which you can consider connecting an external sensor
   * [[ExternalSensorList|List of supported sensors]] - A list of sensors for which the DSMLink application includes display routines   * [[ExternalSensorList|List of supported sensors]] - A list of sensors for which the DSMLink application includes display routines
-  * [[ECUWiringInformation||ECU wiring information]] - Pin-outs and MFI circuit schematics for the 1G and 2G DSMs+  * [[ECUWiringInformation|ECU wiring information]] - Pin-outs and MFI circuit schematics for the 1G and 2G DSMs 
 + 
  
-===== Exceptions, ​issues or special cases =====+===== Exceptions, special cases and examples ​=====
  
   * [[ECUInputData|Buffering ECU inputs]] - Some sensors can't properly drive certain inputs on our ECU.  This page describes the solution.   * [[ECUInputData|Buffering ECU inputs]] - Some sensors can't properly drive certain inputs on our ECU.  This page describes the solution.
Line 17: Line 26:
   * [[BlownSensorGround|Checking for a blown sensor ground]] - Here's how to check to see if you've blown your sensor ground track in the ECU   * [[BlownSensorGround|Checking for a blown sensor ground]] - Here's how to check to see if you've blown your sensor ground track in the ECU
   * [[InnovateLC1orLM1Install|Innovate LC-1 or LM-1]] - Special consideration and example install   * [[InnovateLC1orLM1Install|Innovate LC-1 or LM-1]] - Special consideration and example install
 +  * [[GM3BarInstall|GM 3 or 3.3 bar]] - Installation example for the GM 3 or 3.3-bar on a 2G wired into the MDP sensor input
  
installnewsensor.1201092640.txt.gz · Last modified: 2008/01/23 07:50 by 76.100.119.159