User Tools

Site Tools


diagport-12pin

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
diagport-12pin [2009/11/16 08:44]
twdorris
diagport-12pin [2024/03/15 11:16] (current)
Line 4: Line 4:
 The following 3 wires are the wires used by the ECMLink datalogging cable. The following 3 wires are the wires used by the ECMLink datalogging cable.
  
-{{  ​http://​www.ecmtuning.com/​images/​forums/​ecudocs/​diagport1g.png ​ }} \\+{{  ​https://​www.ecmtuning.com/​images/​forums/​ecudocs/​diagport1g.png ​ }} \\
 The "front side" view is looking at the diagnostic connector in the car with the male pins pointing out at you.  The "​reverse side" view is looking at the connector end of our cable (looking "​into"​ the female sockets). The "front side" view is looking at the diagnostic connector in the car with the male pins pointing out at you.  The "​reverse side" view is looking at the connector end of our cable (looking "​into"​ the female sockets).
  
Line 13: Line 13:
 Pins 1 and 10 **should** have connectivity back to pins on the ECU.  Check that this is true. Pins 1 and 10 **should** have connectivity back to pins on the ECU.  Check that this is true.
  
-For a 1G DSM ECU, pin 1 of the diagnostic connector should connect with pin 1 on the ECU.  Pin 10 of the diagnostic connector should connect with pin 2 on the ECU.  For 1G DSM ECU wiring information,​ view the [[http://www.dsmlink.com/​images/​forums/​1GECUPinout.pdf|1G ECU Pinout]] document found on our [[ecuwiringinformation|ECU wiring page]].+For a 1G DSM ECU, pin 1 of the diagnostic connector should connect with pin 1 on the ECU.  Pin 10 of the diagnostic connector should connect with pin 2 on the ECU.  For 1G DSM ECU wiring information,​ view the [[https://www.ecmtuning.com/​images/​forums/​1GECUPinout.pdf|1G ECU Pinout]] document found on our [[ecuwiringinformation|ECU wiring page]]. 
 + 
 +For an EVO1-3 ECU, pin 1 of the diagnostic connector should connect with pin 42 on the ECU.  Pin 10 of the diagnostic connector should connect with pin 43 on the ECU.  For EVO1-3 ECU wiring information,​ refer to [[https://​www.ecmtuning.com/​images/​forums/​EVO%20I-III%20ECU%20COLOUR%20PINOUTS.pdf|this document]] put together by the fine folks at [[http://​www.evocoupe.net/​forum/​|www.evocoupe.net]].
  
-For an EVO1-3 ECU, pin 1 of the diagnostic connector should connect with pin 42 on the ECU.  Pin 10 of the diagnostic connector should connect with pin 43 on the ECU.  For EVO1-3 ECU wiring information,​ refer to [[http://​www.ecmtuning.com/​images/​forums/​EVO%20I-III%20ECU%20COLOUR%20PINOUTS.pdf|this document]] put together by the fine folks at [[http://​www.evocoupe.net/​forum/​|www.evocoupe.net]]. 
diagport-12pin.1258379087.txt.gz · Last modified: 2009/11/16 08:44 by twdorris