ecmlink101initialchecks
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
ecmlink101initialchecks [2010/01/28 04:37] twdorris |
ecmlink101initialchecks [2024/03/15 11:16] (current) |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| ==== Base MAF type ==== | ==== Base MAF type ==== | ||
| - | {{http://www.ecmtuning.com/images/forums/ecmlink101/basemafclip.png}} | + | {{https://www.ecmtuning.com/images/forums/ecmlink101/basemafclip.png}} |
| In the ECU Config -> MAF Comp tab, check your Base MAF type. This should say something like "Stock", "3G/EVO8", "GM 3in", etc. You want to make sure this matches what you actually have installed on the car. If you have a GM MAF Translator device made by Full Throttle (as opposed to running the GM MAF directly into the ECU using our cable), then you'll want to select "Stock" because the translator is supposed to provide a signal to the ECU that more or less simulates a stock Mitsubishi airflow sensor. | In the ECU Config -> MAF Comp tab, check your Base MAF type. This should say something like "Stock", "3G/EVO8", "GM 3in", etc. You want to make sure this matches what you actually have installed on the car. If you have a GM MAF Translator device made by Full Throttle (as opposed to running the GM MAF directly into the ECU using our cable), then you'll want to select "Stock" because the translator is supposed to provide a signal to the ECU that more or less simulates a stock Mitsubishi airflow sensor. | ||
| Line 17: | Line 17: | ||
| ==== Global fuel ==== | ==== Global fuel ==== | ||
| - | {{http://www.ecmtuning.com/images/forums/ecmlink101/fuelclip.png}} | + | {{https://www.ecmtuning.com/images/forums/ecmlink101/fuelclip.png}} |
| Go to the ECU Config -> Fuel tab and check the global fuel adjustment slider. This one is a bit more complicated to explain simply because there are a lot of things you can do to your car's setup that will affect this value. These things include: | Go to the ECU Config -> Fuel tab and check the global fuel adjustment slider. This one is a bit more complicated to explain simply because there are a lot of things you can do to your car's setup that will affect this value. These things include: | ||
| Line 27: | Line 27: | ||
| To help with this, there is a "calculate" button on the Fuel tab near the Global fuel adjustment area. Click this Calculate button and enter appropriate values for your specific setup. The following screenshot shows a "typical" FIC 850 configuration on gasoline with a 2G ECU. | To help with this, there is a "calculate" button on the Fuel tab near the Global fuel adjustment area. Click this Calculate button and enter appropriate values for your specific setup. The following screenshot shows a "typical" FIC 850 configuration on gasoline with a 2G ECU. | ||
| - | {{ http://www.ecmtuning.com/images/forums/ecmlink101/fuelcalc.png }} | + | {{ https://www.ecmtuning.com/images/forums/ecmlink101/fuelcalc.png }} |
| 1G ECU will default to a different base fuel value (37psi). Adjust this only if you've installed an aftermarket fuel pressure regulator or you know your car is running some different pressure than the default. | 1G ECU will default to a different base fuel value (37psi). Adjust this only if you've installed an aftermarket fuel pressure regulator or you know your car is running some different pressure than the default. | ||
| Line 67: | Line 67: | ||
| Get AFRatioEst in your graph legend and then edit the display preferences (follow the same procedure as outlined above for BoostEst). You'll need to configure the preferences as exactly as possible. Provide information on injector size, your configured deadtime adjustment, and base fuel pressure. You also need to configure information about the fuel you're running. If you're running regular pump gas, then just leave the defaults of 14.7:1 for actual stoich ratio and 0.760 for specific gravity. The following shows a typical 2G setup configured for 850 injectors and pump gas. | Get AFRatioEst in your graph legend and then edit the display preferences (follow the same procedure as outlined above for BoostEst). You'll need to configure the preferences as exactly as possible. Provide information on injector size, your configured deadtime adjustment, and base fuel pressure. You also need to configure information about the fuel you're running. If you're running regular pump gas, then just leave the defaults of 14.7:1 for actual stoich ratio and 0.760 for specific gravity. The following shows a typical 2G setup configured for 850 injectors and pump gas. | ||
| - | {{ http://www.ecmtuning.com/images/forums/ecmlink101/afratioestprops.png }} | + | {{ https://www.ecmtuning.com/images/forums/ecmlink101/afratioestprops.png }} |
| If you're running a 1G manual transmission car with the stock fuel pressure regulator, then your fuel pressure will be 37psi. If you're running a 1G automatic transmission car with the stock automatic fuel pressure regulator, then you'll use 43.5psi. | If you're running a 1G manual transmission car with the stock fuel pressure regulator, then your fuel pressure will be 37psi. If you're running a 1G automatic transmission car with the stock automatic fuel pressure regulator, then you'll use 43.5psi. | ||
| + | |||
ecmlink101initialchecks.1264671469.txt.gz ยท Last modified: 2010/01/28 04:37 by twdorris
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
