ECMTuning - wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

<h1>Supported Aftermarket Sensors</h1> <div class="level1"> <p> The lists below detail which sensors the DSMLink application supports for datalogging. Others can be added fairly easily, but this does require a new application build and so this doesn't happen very often. </p> </div> <h2>Wideband O2 kits</h2> <div class="level2"> <ul> <li class="level1"> AEM with and without gauge</li> <li class="level1"> Dyno Jet</li> <li class="level1"> FJO</li> <li class="level1"> <a href="/wiki/doku.php?id=innovatelc1orlm1install" class="wikilink1" title="innovatelc1orlm1install">Innovate LM-1 & LC-1</a> (see note below)</li> <li class="level1"> PLX M-series</li> <li class="level1"> Techedge v1 and v2</li> <li class="level1"> Zeitronix ZT-2</li> <li class="level1"> NGK AFX</li> </ul> </div> <h2>Boost pressure sensors</h2> <div class="level2"> <ul> <li class="level1"> AVCR 3 and 4-bar</li> <li class="level1"> GM 3 and 3.3-bar (P/N info below)</li> <li class="level1"> AEM 3.5 and 5-bar</li> <li class="level1"> Apex'I EL series</li> <li class="level1"> Greddy 52mm and 60mm</li> <li class="level1"> Turbo XS sensors</li> </ul> </div> <h2>Miscellaneous</h2> <div class="level2"> <ul> <li class="level1 node"> Autometer fuel and oil pressure (sensor #2246)<ul> <li class="level2"> Note: this is apparently <a href="http://www.kavlico.com/pages/products_sensors/pressure_sensors/standard_designs1.htm#p265" class="urlextern" title="http://www.kavlico.com/pages/products_sensors/pressure_sensors/standard_designs1.htm#p265" rel="nofollow">Kavlico's P265 sensor</a>. Further discussion can be found on the Innovate Motorsports threads <a href="http://www.innovatemotorsports.com/forums/showthread.php?t=1108" class="urlextern" title="http://www.innovatemotorsports.com/forums/showthread.php?t=1108" rel="nofollow">here</a> and <a href="http://www.innovatemotorsports.com/forums/showthread.php?t=662" class="urlextern" title="http://www.innovatemotorsports.com/forums/showthread.php?t=662" rel="nofollow">here</a>.</li> </ul> </li> <li class="level1"> GM intake air temperaure (P/N info below)</li> <li class="level1"> MSD Air Intake Sensor #2320</li> <li class="level1"> Apex'I EL EGT</li> </ul> </div> <h2>Part number information</h2> <div class="level2"> <ul> <li class="level1"> GM Intake Air Temperature P/N 25036751, pig tail 12102620 <a href="http://www.gmpartsdirect.com/" class="urlextern" title="http://www.gmpartsdirect.com/" rel="nofollow">GM Parts Direct</a></li> <li class="level1"> GM 3-bar P/N 12223861, pig tail 15305891 <a href="http://www.gmpartsdirect.com/" class="urlextern" title="http://www.gmpartsdirect.com/" rel="nofollow">GM Parts Direct</a></li> <li class="level1"> GM 3.3-bar P/N 9373269, pig tail 88987997 <a href="http://www.gmpartsdirect.com/" class="urlextern" title="http://www.gmpartsdirect.com/" rel="nofollow">GM Parts Direct</a></li> </ul> <p> <b>LM1/LC1 note</b> - These have programmable outputs. Which means there is no "standard" display conversion format. So what we suggest you do is to program the output to mimic another device that we do support. Typically this would be the linear TechEdge output that has 9:1 mapped to 0v and 19:1 mapped to 5v. Then you would datalog this as the linear TechEdge (TEWBLin). </p> </div>